Home > Products > Roll-N-Go Roller Ramp Accessories
Sort By:
Page of 1
Ground Anchor Roller Set - Model50/1200/pontoon Cable Length Upgrade for Manual Winch
Ground Anchor
Our Price: $9.99
anchor only 2 rollers, 2 brackets, hardware

Use this cable if you choose the manual winch and your total track length is longer than 60 feet or you are doubling the cable with a total track length longer than 36 feet. Avoid loading extra cable that you don't need. With more cable on the drum, more cranking force is required.

Basic Leg Kit Angle Brace Kit Roller Set – Model 2000
Basic Leg Kit
Our Price: $129.99
Angle Brace Kit
Our Price: $139.99
Roller Set – Model 2000
Our Price: $164.99

All aluminum leg support kit for Models 750, 1200, 2000 and Pontoon. Includes (2) pipe brackets with double set crews, (2) foot pads with single set screws and stainless steel mounting hardware. Customer supplies readily available 1-1/4" I.D. pipes. From Roll-n-Go Shore Docking Systems.

Use with Basic Float Kit 4 rollers, 2 axles, hardware
Drop Roller Kit Winch Upgrade - Autobrake Extra Float (380 lbs. bouyancy ea.)
Drop Roller Kit
Our Price: $174.99
Winch Upgrade - Autobrake
Our Price: $199.99
Use with Basic Float Kit. Call or email us for detailed brochure explaining the Roll-n-Go Float Kits. Winch Upgrade – 1500 lb (dead-lift) Autobrake: Automatically stops if
you release the handle for extra safety. Includes 50′ cable (Replaces
1700 lb winch). The 1500 Autobrake Winch works with Roll-n-Go models
1200, 2000 and Pontoon. The price listed is only valid when ordering a
complete kit and upgrading the standard winch. To purchase the Autobrake
winch separately the price is $169.99. Please call us if ordering
without a kit. (Not available on PWC or 750)

Includes beam mounting hardware **Each Float has 380lb Bouyancy. Dimension : 72" x 24" x 8"

Angle Connector Kit 7.5 degree pair Wide Support Kit - 8.5' Leg Kit 1 1/2 ft. One pair.
Wide Support Kit - 8.5'
Our Price: $239.99
Replace a straight connector with this kit. Creates a 7.5 degree angle
whe need to follow terrain . NOTE: YOUR RAMP SHOULD HAVE A POSITIVE
ANGLE TOWARD THE WATER ALONG IT’S ENTIRE LENGTH. The system relies on
gravity to move the boat into the water and to create the proper tension
on the cable when rewinding.
8.5′ Wide All-Aluminum Wide Support Kit with stainless steel hardware.
Provides better lateral support for longer ramps. Must be ordered with
(1) Basic Leg Kit in a set. From Roll-n-Go Shore Docking Systems.

Leg kits are used when its necessary to span over rough terrain and blocking is not practical. Each kit comes with 2 - 1 1/2Ft long legs of 1 1/2 inch aluminum schedule 80 pipe along with the bracing and hardware necessary. Requires the use of a drill and 1/2" drill bit to custom locate and plumb the legs. Rails should be supported about every 9 feet for boats under 2000 lbs and about every 4 1/2 feet for boats over 2000 lbs. Comes with 12 inch square foot plate for the base of the leg.

Leg Kit 3 ft.  One Pair Float Kit Basic** - (Ships in 2 Cartons)
Leg Kit 3 ft. One Pair
Our Price: $399.00
Leg kits are used when its necessary to span over rough terrain and blocking is not practical. Each kit comes with 2 - 3 ft long legs of 1 1/2 inch aluminum schedule 80 pipe along with the bracing and hardware necessary. Requires the use of a drill and 1/2" drill bit to custom locate and plumb the legs. Rails should be supported about every 9 feet for boats under 2000 lbs and about every 4 1/2 feet for boats over 2000 lbs. Comes with 12 inch square foot plate for the base of the leg.

Roll-n-Go's all new Float Kit is perfect for marinas and deep water applications where in-water boat lifts are impractical or impossible. Take our model 1200 or 2000 and create a floating boat ramp for use with your dock or shore wall. Call or email us for detailed brochure explaining the Roll-n-Go Float Kits.

Unlike expensive floating boat lifts, our system requires no outside power source. Its modular design gives it the versatility for many sizes of boats up to 2,000 lbs. - just add more floats. Durable rotational molded floats are filled with closed-cell polystyrene for a long-lasting leak-free life. Just like every Roll-n-Go quality product, the float kit is designed for easy UPS shipping. Now your valuable watercraft investment can sit safely and cleanly out of the water. It's also protected from the bumps and scrapes that can happen in marinas and other environments with lots of watercraft traffic. Hinges at front of system mount to dock or shore wall. Easy-to-understand instructions for mounting to truss style and wood sided docks. Docking your boat with our float system is just as easy as with any of our shore systems: Just pull up to the end of the system, hook on the strap and crank your watercraft safely out of the water.